Install baseboards metal studs




















Steel studs are often used in commercial construction as well as in some residential homes. You won't know they're metal when the studs are clad in drywall -- until you hit one with a nail or screw when attempting to hang something.

Most screws and nails won't penetrate through steel studs. Drilling a hole is required. If you don't have a stud finder, there are several methods that can be effective in finding studs. When a home is framed, the wall studs are usually spaced 16 or 24 inches apart. If you start in a corner and measure out 16 inches and you don't find a stud , you should find one at 24 inches. How to Install Baseboards on Metal Studs. Spread construction adhesive in a zigzag pattern across the back of the baseboard.

Press the board into place and hold it steady for a moment. Nail one or two more finish nails along the length of the baseboard for added stability. Can you hang a flat screen TV on metal studs? Metal studs are hollow and narrow, so you'll need hardware that will be strong enough to support the weight of the television and long enough to reach the studs.

Snap toggles are stronger than a toggle bolt or drill toggle and can be used as an anchor for installing a flat screen TV through metal, drywall, and plaster. Do you have to nail baseboards into studs? Base molding fits flush along the bottom of the wall and typically attaches to the wall studs and to the floor plate. Can you install shelves on metal studs? Metal studs are lighter and sometimes less expensive than wood, and they are consistently straight.

In conventional construction, hanging shelves on a wall requires finding the studs in the wall and mounting the shelf brackets to the studs with screws. Toggle bolts work better than screws with metal studs. That leaves two options: attaching them to the wall studs or gluing them to the wall covering. When the studs are wood, you can nail the baseboards with finish nails, but that won't work with metal studs. Builders who use metal studs recommend three alternative methods.

These screws have undersized heads, somewhat like finish nails. To attach a board, set it in place and drive the screw through the board and the drywall with a drill and appropriate screw bit, and keep pushing when it contacts the metal stud.

It will tap its own hole and penetrate the metal in a few seconds. Drive the screws in pairs so that one is holding the top edge of the baseboard and one is holding the bottom.

Also, the house won't shake so much when your teenager slams their bedroom door! Helpful 17 Not Helpful Grip the back of the stud flange near the screw connection point with your fingers in order to give it support and then drive the screw. Helpful 21 Not Helpful Some people find it well worth the extra money to use stiffeners or 20 gauge studs rather than the usual 25 gauge ones. The walls feel more solid and the cost difference typically isn't all that much. Helpful 3 Not Helpful 1.

Helpful 11 Not Helpful Make sure that your architect or designer's plans aren't drawn for wood dimensions. Helpful 9 Not Helpful 5. For heavy cabinets such as overhead kitchen cabinets, keep in mind that steel studs may not be strong enough to support their weight, even with drywall on them. Install solid wood blocking to these areas to help hold up the cabinets. Doing any type of work using power tools while tired or in a rush may lead to injury.

Helpful 8 Not Helpful 9. It will not hold. Instead, use specially designed trim screws for the job. Helpful 2 Not Helpful 0. Cut steel is sharp, so make sure to wear gloves. Helpful 1 Not Helpful 0. Wear eye protection when cutting steel and driving screws.

It's not unheard of for a screw to jump off the power screwdriver and shoot out at you. You Might Also Like How to.

How to. About This Article. Co-authored by:. Co-authors: Updated: August 21, Categories: Featured Articles Building Walls.

Article Summary X To install metal studs, determine how many studs you'll need by measuring the area, keeping in mind that you will need to install 1 stud every 12 inches.

Italiano: Costruire l'Intelaiatura in Metallo di una Parete. Thanks to all authors for creating a page that has been read , times. Worked better than I expected and is easy to move; much better than using 2x4 lumber.

Great article for the DIY'er to read. More reader stories Hide reader stories. Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy.

Mark Saragian Dec 9, Mark Thomas Mar 9, I am finishing my entire basement using steel studs. Philip Newman Mar 8, Thanks for the help!

Anonymous Aug 4, I just started in this business of steel framing, so to me it was very educational. Robert Peterson Nov 23, Share yours! More success stories Hide success stories. Featured Articles How to. Trending Articles How to. New Pages How to.



0コメント

  • 1000 / 1000